Forum and Costume Controls

   FAQFAQ  SearchSearch  MemberlistMemberlist   UsergroupsUsergroups  medals.php?sid=616e053098b93ff3384964501d243cbdMedals   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in

       
REMINDER: Do not change your e-mail address yourself. Please read this first for why.

The Effects Lab Multi Piece Prosthetics tutorial

 
Post new topic   Reply to topic    Rebel Legion Forum Index -> Costume and Prop Making -> TUTORIALS -> Tools and Techniques
View previous topic :: View next topic  
Author Message
Wolfie (Crystal Bass)
Active Legion Member


Joined: 01 May 2005
Posts: 8081
Location: Tennessee
Medals: 5 (View more...)
Colorado Wildfires 2012 Relief Award (Amount: 1)

PostPosted: Wed Dec 01, 2010 5:04 pm    Post subject: The Effects Lab Multi Piece Prosthetics tutorial Reply with quote

The Effects Lab Multi-Piece Prothetics Tutorial by Dan Kurz

http://www.theeffectslab.com/kurzprosthetic.htm

You will need to read how to make a face-cast before attempting this tutotial! http://www.rebellegion.com/forum/viewtopic.php?t=28460

To start, I took the life cast of the model and made a simple silicone brush up mold. Half the cast was molded from the ears forward and down past the collar bone. I then cast a hydrocal duplicate of his cast. You must make sure to keep the hydrocal thin. Hoydrocal is used due to the fact that it is porus and will absorb water in the floating stage. Once the duplicate cast is done it is coated 2 or 3 times with Alcote. Alcote is a dental separator and is available from most FX shops or your local dental supply house. Alcote shrinks a little as it dries, so if it flakes off, you have added too much….shame on you. You will know if it had dried if it has a slight eggshell sheen to it…and it’s not wet.



I have based this makeup on an elderly Native Canadian male. You can now begin sculpting the character on top of the cast as normal. Remember to keep the areas where the makeup will split thin. I sculpted the prosthetics as far as the detail. I didn’t add the texture as some will be lost during the floating and separating.



Here is a lesson in multi tasking; you should be making your positive molds while you are sculpting. I used the same silicone mold and poured in ultra cal 30 in the desired areas. I needed positives for the chin, forehead, neck, sides of the face and the nose/upper lip. These casts need a base to sit on so, when the individual casts are done, they need to be soaked for 30 min in water. This soaking ensures that the casts will adhere to fresh plaster. To make the bases, I used a roll of carpet with the rubber backing and cut them into strips. The strips are rolled up and made into tubes a little larger than each cast. The tubes are placed on a level surface and filled approx 4-5 inches full of ultracal 30. If the molds are to be used for multiple baking’s, it is advisable to reinforce them with metal mesh. Make a ring about an inch smaller than the diameter of the tube and place it in the tube before pouring the plaster. This acts the same as the rebar in concrete structures. Once the plaster has creamed (firm but still wet) the casts are imbedded into them. I blend the wet plaster to the cast with a brush.



Once the molds are done and the sculpt is complete, the life cast is then dunked in water. This is called floating. Before you dunk, use a sharp exacto knife and cut the sculpt where you want to divide it. You should use a large Rubbermaid bin or a garbage can and fill it with clean water. The cast should be submerged and left to sit for a few hours. To be safe, I let mine sit overnight. The water will seep into the porus hydrocal and re-activate the alcote in the other side. It will become wet and slippery and cause the clay to fall off. This is called floating because, in theory, the pieces should float off the cast, pretty clever huh? Don’t be so optimistic, you still have to pry off the pieces and large sections may have to be cut in half. I use a slurpee spoon straw to pry off the clay. Be gentle and patient. Dick Smith recommended to me that one use a water pic to aid in removal. Water could be blasted under the clay and force them off. I have not tired this but it sounds like it would work well.





You should now have the pieces separate and on the positives. It is now a matter of sculpting the detail and the blending edge. But what if you have pieces that are too thick to overlap? Areas like the jowls and chin can be too thick to overlap. There is a solution. Cut the pieces as normal and remove the chin for example. Clay is added to the two jowl edges to blend off to the life cast where the chin was. You then make an alginate mold of the area and cast your positive from that. You can then place the chin section on the cast and blend it to the jowls. Now it overlaps.





Once the prosthetics are too your liking, the cutting edge and the flashing are sculpted as usual. I used water based clay. I also added small rectangular holes in the flashing. This is to take some of the pressure off the cutting edge. This it not necessary, only a personal thing. The same effect is achieved with drilled keys.





The sculptures can now be lightly sealed. Try not to get much in the blending edge as it can affect its thickness.

The carpet is again wrapped around the positives and taped closed. Ultracal is mixed and poured in as before. The molds are left to cure and later pried open. Clean the molds and drill a small vent hole in the center of the positive. I drilled mine in the center of the cheek, tip of the nose, center of the forehead and center of the chin. The neck was injected so numerous vent holes were drilled in the perimeter of the appliance and 1 injection hole in the center.




From here it is a matter of running the prosthetics and doing the application.






Back to top
View user's profile Send private message Send e-mail Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Rebel Legion Forum Index -> Costume and Prop Making -> TUTORIALS -> Tools and Techniques All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot post calendar events in this forum
The Rebel Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred volunteer Rebel costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © 2014 Lucasfilm Ltd. & ™ All rights reserved. Used under authorization.


Powered by phpBB © 2001, 2005 phpBB Group