Forum and Costume Controls

   FAQFAQ  SearchSearch  MemberlistMemberlist   UsergroupsUsergroups  medals.php?sid=21bf25711cf53da54669005a84a79de9Medals   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in

       
REMINDER: Do not change your e-mail address yourself. Please read this first for why.

Rebel Pilot Costume Standards

 
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> COSTUME STANDARDS
View previous topic :: View next topic  
Author Message
JediMom3 (Andrea Samulewicz)
Active Legion Member


Joined: 21 Dec 2003
Posts: 1966

Medals: 1 (View more...)
Rebel Legion CV Supporter (Amount: 1)

PostPosted: Thu Aug 02, 2007 7:11 am    Post subject: Rebel Pilot Costume Standards Reply with quote

NOTE: The costume standards are a guide, yet are not an all inclusive outline of required elements. The judges will be looking for quality of workmanship, accurate execution and use of materials in addition to these general standards check lists. If you have a question about fabrics, colors, and parts choices for your build please contact the LCJs for your category about parts/materials you are considering before you start your build. (LCJ listing here)

Rebel Pilot Costume Standards
X-Wing pilot (Episode IV; VI), Y-Wing pilot (Episode IV)

Required Items:

1.Orange flightsuit with the following details:


a. Code cylinder pocket on outside of upper-middle left arm.
b. Rectangular pocket with a flap closure on upper-middle right arm. Flap should be rectangular shaped.
c. Comm pad pocket on outside of left forearm above wrist.
d. Thigh pockets with rectangular flap closures (upper set required, lower set optional).

e. No visible zippers or snaps.
f. Mandarin-style with pointed tab closure. Collar closes from left to right with the exposed tab on the right side of the throat.

f. Cuffs should close in a similar fashion as the Mandarin-style collar.

2. Mid-calf black boots (Jack boots or engineer boots are acceptable). Leather pull-on style preferred with low heels.
a. Boots should be largely unadorned. No laces or ankle buckles (small buckle at top edge of boot allowable if covered by blousing).
b. No non-black zippers. Any zipper closure must either be hidden or on the inside of the boot (that is, front and outside zippers are not permitted).
c. High-Calf boots are acceptable with sufficient blousing of the flighsuit legs.


3. Silver/grey leg flares in an olive drab or black leg-band holder.
a. Maximum of 8 flares per holder.
b. Flares and flare holder should be approximately 4" (inches) long.
c. Metal leg flares are preferred, but other materials are permitted as long as, when finished, give the appearance of being silver metallic in appearance.
d. Leg flares should be spaced equidistant around the leg.

e. Leg flares can be worn on either leg and should be positioned to so the bottom edge of the leg flare is resting on the top of the boot (that is, no gap between the flare holder and the top of the boot).


4. Light grey/silver grey ejection harness and web belt.
a. Harness and belt are made of strapping material that is 2” (inches) wide.
b. Front and back straps extend up the torso under the flack vest and are secured to either the flightsuit or to the inside the flak vest panels. Attachment must be hidden by the flak vest. The lower part of the harness should fall (or loop) just below the inseam (or crotch area).
c. Two loops of strapping are connected to the front-back strapping (at the lowest part of the front-back loop) and loop around each leg, drooping no lower than the knees.

d. The belt is worn over the front/back harness strap and is closed with a silver/gray "cargo slide" (or roll pin) style buckle. The free end of the belt is looped around the slide so that the excess belt is on the underneath/inside of the belt, not on top/outside of the belt. The right side of the belt contains 6 (six) vertical loops for mini-flares. Mini-flares are made of metal or other materials that, when finished, have a metallic silver appearance.


5. Flak Vest, consists of white front and back cloth (ballistic nylon or similar fabric) panels, contoured to fit over the chest and back where the two panels are of a similar shape/size. The two panels are connected together by straps over the shoulder and under the arms. The flak vest MUST be proportional to the wearer (this is NOT one-size-fits-all), and the following details must be included:

a. The top of the front and back panels should begin at the base of the collar in front and approximately two inches below the collar in back. (Please refer to the reference pics where the flak vest begins right under the mandarin collar.)
b. The bottom of the front and back panels are even and should completely cover the chest while not extending toward the waist any further than one-half to two-thirds the distance from the arm pit to the waist, and should allow for approximately 3” (inches) of visible flightsuit above the top of the belt.
c. The front panel has a series of horizontal ribs. The ribs are created by inserting 0.25" (inch) OD tubing (or similar sized material) through fabric tubes prepared for the tubing. Ribs are separated from each other by a space that is the same width as the finished rib.
The pattern for rib placement on the front of the flak vest is as follows (from top to bottom):
i. Two equally spaced ribs at the top (near the collar).
ii. Immediately below the two top ribs there is a flat wide area with eight horizontal rows of top stitching that is approximately 0.25" (inch) apart (for a total of approximately 2” (inches) of flat area). This area is sometimes referred to as "The Gap".
iii. The remainder of the front panel, below the “The Gap” just described, contains a minimum of 8 – 9 ribs (total number of ribs will depend on the size of the wearer) that continues to the bottom edge of the front panel.
Note: The side strap (described in 5.g. below) does not cross over the front panel. Vests with a missing rib on the lower front panel will not be approved.

d. The back panel has a minimum of 16 equally spaced ribs (based on Luke's ANH flak vest), again, the total number of ribs will depend on the size of the wearer). Again, the ribs are created by inserting 0.25" (inch) OD tubing (or similarly sized material) through fabric tubes prepared for the tubing. Ribs are separated from each other by a space that is the same width as the finished rib. In addition, “The Gap”, as seen on the front panel is NOT present on the back panel.
e. Ribbing on the front and back panels stop no more than one inch from each side (on left and right).
f. The shoulder straps are approximately 2" (inches) wide and sewed in place to the inside of the flak vest panels, thus joining the front and back panels together. Each shoulder strap has rows of horizontal top-stitching (each about 0.25" (inch) apart) across the short length of the strap (or perpendicular to the length of the strap). These stitches cover the entire strap, from front to back.
g. The under-arm straps have one silver "press-release" style buckle on the left and right sides of the vest. The female half of the buckle is sewn to edge of the front panel. The male end is sewn to the end of the strap. Each strap continues back under the arms, and passes through a short sleeve sewn above the second or third rib from the bottom of the back panel. The left and right straps meet in the center, and are adjusted with a black/dark-grey "strap adjuster" style buckle. The excess strap lengths are either trimmed to length or tucked into the sleeves to present a neat appearance. These side straps should ride approximately 2" - 4" (inches) below the armpit depending on the size of the wearer.


h. Be careful when checking references. When filming The Empire Strikes Back, the flak vests were worn “backwards” when compared to ANH and ROTJ.

Note: Please be aware that flak vests from commercial vendors must meet costume standards and be screen accurate. Some commercially available flak vests require extensive modifications for approval.

6. Accurate sized grey chest box with accurate decorations and details as follows:

a. Raised buttons (acrylic preferred) with acceptable color schemes.
b. Separated rocker switches.
c. Accurate knobs (metal or other materials that when finished have a metallic silver appearance.), details, pin stripes etc.
d. 1" - 1.25" (inches) diameter ribbed grey hose or aviation hose. One end of the hose should attach at the left-bottom of the chest box and the other end should connect to the suit in some screen-accurate manner (tucked up into the flak vest, attached to flightsuit, etc.).
e. Chest box is secured around the collar and the back with olive drab nylon/polypropylene/polyester/cotton(canvas) straps. The strap around the collar has no fasteners. The strap around the back has a silver or black "strap adjuster" style buckle in the back. Excess strap from should be either trimmed or otherwise hidden to present a neat appearance.


f. The Chest box is worn low on the chest (with the top of the box near the bottom of "The Gap") so the bottom (around the back) strap passes below or along the bottom of the front flak vest panel.
g. (LINK TO PILOT FORUMS where box design pics are located).

7. Code Cylinders (Arm Tools) in left shoulder pocket.
a. Two minimum, four maximum. Metal or other materials that when finished have a metallic silver appearance.
b. Cylinder heads showing should resemble screen accurate representations.


8. Black gauntlet-style gloves.
a. Leather or pleather gloves preferred. Cloth or rubber gloves are not permitted.
b. The cuff of the gauntlet must present a "flared" appearance when worn.


9. Accurate Comm Pad (size, details, 3-dimensional, coloration, etc.) visible in the comm pad pocket.


Formal Requirements:
You must have at least one of the following items to be accepted:

1. X-Wing helmet with Star Wars-style decoration.

a. Helmet has a Mohawk design and raised side panels as seen in the films.
b. Trapezoidal cap on the front of the Mohawk with the appropriate design.
c. Amber or dark grey colored visor covering the eyes (maybe be fixed or movable).
d. White chin cup with black elastic straps. Elastic straps should be fixed to the inside of the helmet.
e. Black weather stripping around the “ears” and neck borders.
f. Paint scheme, including pin stripping and decorations should resemble those seen in the films. Blatant “modern-world” or other sci-fi-fantasy genre images/designs are NOT permitted. Helmets should look as though they belong in the Death Star Trench sequence.
g. Tutorial for Pilot helmet assembly is found here: http://www.rebellegion.com/forum/viewtopic.php?t=18735
h. Original Trilogy Pilot Helmet Gallery is found here: http://www.rebellegion.com/forum/viewtopic.php?t=41855

2. Mini-flares on belt. A mix of filled and empty slots are okay.
a. Metal or other materials that, when finished, have a metallic silver appearance.

3. Accurate belt buckle on web belt, as described in 4.d.


(NOTE – All references above to "screen" or "accurate" are indicators that you should be comparing and matching closely to screen-cap reference examples. Always refer to reference pictures for details of construction.)

Costume Resources:
  1. Alderaan Base X-Wing Pilot Tutorial
  2. Richie's Armor X-Wing Helmet Tutorial
  3. Parts of Star Wars Luke X-Wing Pilot page
  4. Parts of Star Wars X-Wing Pilot page



Updated: November 2, 2013

Costume Standards Committee Review: August 27, 2013 – October 23, 2013
Rebel Legion Starfighter Command Forums Review: April 4, 2013 – October 31, 2013.


===========================================
Snowspeeder pilot (Episode V)



Required Items:

  1. Orange flightsuit with mandarin-style collar and pointed tab, code cylinder pocket on upper-middle left arm, rectangular pocket with a flap closure on upper-middle right arm, comm pad pocket on outside of left forearm above wrist, and thigh pockets (upper set required, lower set optional). No visible zippers or snaps.
  2. Orange flight jacket with padded collar and ribbed strips down both arms.
  3. Tan/grey Hoth-style boots and gaiters with accurate movie-style strapping or mid-calf black boots (If using the black boots ––– jack boots or engineer boots are acceptable. Leather pull-on style preferred with low heels. No laces. No ankle buckles (small buckle at top edge of boot allowable if covered by blousing). No non-black zippers. Any zipper closure must either be hidden or on the inside calf. No zippers on front or outside calf of boots. High-Calf boots are acceptable with sufficient blousing of the flighsuit legs.
  4. Silver/grey leg flares in an olive drab or black leg-band holder. Maximum of 8 flares per holder. Flares should be approximately 4" long.
  5. Light grey/silver grey ejection harness and web belt, all 2” wide.
  6. White flak vest with accurate ribbing and clasps. (ESB Snowspeeder version is worn backwards.) Vest sizing should be proportional to the wearer.
  7. Accurately sized grey chest box with accurate decoration (raised buttons (acrylic preferred, see the Pilot Forums for acceptable button color schemes), separated rocker switches, appropriate materialed greebles, pin stripes etc.). 1" - 1.75" diameter grey hose or aviation hose should attach at the left-bottom of the chestbox and connect to the suit in some screen-accurate manner (tucked up into the flak vest, attached to flightsuit, etc.). (Please note that Costumebase chestboxes will not pass the standards unmodified, however once slightly modified, they will meet standards.)
  8. White and grey gauntlet-style gloves


Formal Requirements:
You must have at least one of the following items to be accepted:

  1. X-Wing helmet with Star Wars-style decoration.
  2. Tan or Beige balaclava or cloth-covered soft helmet, no brim. (design similar, but not exact to the AN-H-15 or British RAF versions.)
  3. Badge in jacket chest pocket along with comm pad on left gauntlet above wrist.
  4. Mini-flares on belt. A mix of filled and empty slots are okay.
  5. Accurate belt buckle on web belt.

Costume Resources:
  1. Alderaan Base X-Wing Pilot Tutorial
  2. Richie's Armor X-Wing Helmet Tutorial
  3. Parts of Star Wars Luke X-Wing Pilot page
  4. Parts of Star Wars X-Wing Pilot page

Revised on June 1, 2010
===========================================
Y-Wing pilot (Episode VI)


Required Items:

  1. Grey/Light Grey flightsuit with either a mandarin-style collar (with pointed tab) or the same tab under another flipped up collar, correct arm pockets (shaped code cylinder pocket on upper left arm, rectangular pocket with a squared-flap closure on upper right arm), and thigh pockets with squared-flap closures (upper set required, lower set optional). No visible zippers or snaps.
  2. Light Tan, Beige, or Taupe cloth or canvas spats over black boots. Leather spats are not acceptable. Spat height should be mid-calf to just under the knee and fall all the way down. Spats should feature an additional strap (w/no buckle) of the same or similar material, running around the length around the calf approximately 1/8-1/4 down from the top of the spat. Spats may feature single or double seam running down the front or back. No laces should be visible. Boots should be mid-calf black boots (Jack boots or engineer boots are acceptable. Leather pull-on style preferred with low heels. No laces. No ankle buckles (small buckle at top edge of boot allowable if covered by blousing). No non-black zippers. Any zipper closure must either be hidden or on the inside calf. No zippers on front or outside calf of boots. High-Calf and Low-Calf boots are acceptable if fully covered by the spats.
  3. White ejection harness and web belt, all 2” wide. Belt may be off-white and is to buckle at the back with a black snap-release buckle. Leg loops are individual per leg and split at the waist. Belt is worn over the harness.
  4. Accurately styled scoop-necked light grey/beige flak cloth or canvas vest with appropriate chest ribbing, shoulder ribbing and small black plastic snap-release buckles on the shoulder straps. Side strapping should be white and 1.5" - 2" wide, shoulder strapping should match front and back panel material. Back panel is smaller and differently shaped than the front but should match front panel material.
  5. Small black/dark grey rectangular chest box on the upper chest. Left side has wide, raised, lined section running vertically.
  6. White oval belly box/tube with black strap and white cloth-covered hose attached at two points (either belly tube to flak vest, belly tube to flightsuit, or flak vest to flightsuit).
  7. Black gauntlet-style gloves (flared leather or pleather preferred, cloth or rubber gloves will not meet standards).


Formal Requirements:
You must have at least one of the following items to be accepted:

  1. Y-Wing helmet with Star Wars-style decoration.
  2. Mini-flares on web belt - a mix of filled and empty slots are okay.
  3. Accurate Comm Pad (size, details, 3-dimensional, coloration, etc.) visible in the correct comm pad pocket on outside left forearm above wrist.

Optional:
  1. Metallic silver Code Cylinders (Arm Tools) in left shoulder pocket. Two minimum; four maximum. Cylinder heads showing should resemble screen accurate representations.

Revised on June 1, 2010
===========================================
A-WING PILOT (Episode VI)


Required Items:

  1. Spruce/Hunter Green flightsuit (no Kelly/Olive Drab/Grass Green) with mandarin-style collar (with squared tab) or same tabbed collar under another flipped up collar, correct arm pockets (shaped code cylinder pocket on upper left arm, rectangular pocket with a squared-flap closure on upper right arm), and thigh pockets with squared-flap closures (upper set required, lower set optional). No visible zippers or snaps.
  2. Light Tan, Beige, or Taupe cloth or canvas spats over black boots. Leather spats are not acceptable. Spat height should be mid-calf to just under the knee and fall all the way down. Spats should feature an additional strap (w/no buckle) of the same or similar material, running around the length around the calf approximately 1/8-1/4 down from the top of the spat. Spats may feature single or double seam running down the front or back. No laces should be visible. Boots should be mid-calf black boots (Jack boots or engineer boots are acceptable. Leather pull-on style preferred with low heels. No laces. No ankle buckles (small buckle at top edge of boot allowable if covered by blousing). No non-black zippers. Any zipper closure must either be hidden or on the inside calf. No zippers on front or outside calf of boots. High-Calf and Low-Calf boots are acceptable if fully covered by the spats.
  3. White ejection harness and web belt, all 2” wide. Belt may be off-white and is to buckle at the front or back with a black snap-release buckle. Leg loops are individual per leg and split at the waist. Belt is worn over the harness.
  4. Accurately styled scoop-necked charcoal/dark grey cloth or canvas flak vest with smaller white front section bib applied over it. (white section should have appropriate ribbing- one above chestbox, 2 below (separated from each other by a gap). This is NOT a duplicate of the X-wing vest. Small black plastic snap-release buckles on the shoulder straps. Side strapping should be white and 1.5" - 2" wide, shoulder strapping should match front and back panel material. Back panel is smaller and differently shaped than the front but should match front panel material.
  5. Accurately styled black upper chest box with accurate ribbing details and black straps.
  6. Accurately shaped white lower chest box (hard or soft) with white cloth-covered hose coming out of the bottom and connecting to flightsuit. This box should be directly under the upper box, with no gap between.
  7. Black gauntlet-style gloves (flared leather or pleather preferred, cloth or rubber gloves will not meet standards).

Formal Requirements:
You must have at least one of the following items to be accepted:

  1. A-Wing hard helmet with Star Wars-style decoration.
  2. Cloth tan AN-H-15 flight helmet (or replica).
  3. Y-Wing helmet with Star Wars-style decoration.
  4. X-Wing helmet with Star Wars-style decoration.
  5. Mini-flares on web belt – a mix of filled and empty slots are okay.
  6. Accurate Comm Pad (size, details, 3-dimensional, coloration, etc.) visible in the correct comm pad pocket on outside left forearm above wrist.

Optional:
  1. Metallic silver Code Cylinders (Arm Tools) in left shoulder pocket. Two minimum; four maximum. Cylinder heads showing should resemble screen accurate representations.

Revised on June 1, 2010
===========================================
B-WING PILOT (Episode VI)


Required Items:

  1. Red flightsuit with open collar (folded down), correct arm pockets (shaped code cylinder pocket on upper left arm, rectangular pocket with a squared-flap closure on upper right arm), and thigh pockets with squared-flap closures (upper set required, lower set optional). No visible zippers or snaps. Black undershirt only required if visible by collar.
  2. Light Tan, Beige, or Taupe cloth or canvas spats over black boots. Leather spats are not acceptable. Spat height should be mid-calf to just under the knee and fall all the way down. Spats should feature an additional strap (w/no buckle) of the same or similar material, running around the length around the calf approximately 1/8-1/4 down from the top of the spat. Spats may feature single or double seam running down the front or back. No laces should be visible. Boots should be mid-calf black boots (Jack boots or engineer boots are acceptable. Leather pull-on style preferred with low heels. No laces. No ankle buckles (small buckle at top edge of boot allowable if covered by blousing). No non-black zippers. Any zipper closure must either be hidden or on the inside calf. No zippers on front or outside calf of boots. High-Calf and Low-Calf boots are acceptable if fully covered by the spats.
  3. White ejection harness and web belt, all 2” wide. Belt may be off-white and is to buckle at the back with a black snap-release buckle. Leg loops are individual per leg and split at the waist. Harness should attach to the drop point at the bottom of the front of the flak vest.
  4. Scoop-necked black, charcoal or dark grey cloth or canvas flak vest with two raised ribs above chest box, small black plastic snap-release buckles on the shoulder straps and a drop-point on the front panel for attachment of ejection harness. Side strapping should be white and 1.5" - 2" wide, shoulder strapping should match front and back panel material. Back panel is smaller and differently shaped than the front but should match front panel material.
  5. Accurately sized and shaped silver/white/light grey chest box made of hard materials with screen-accurate decoration (buttons, knobs, connections, pieces etc.). Chestbox is one-piece - with left and right sides separated by a black painted channel. Chestbox hose should be white cloth-covered and attached from bottom/left/front of box to back of flak vest or tucked in the back of the flak vest. It's drop curve should be around upper thigh length. Black shoulder straps attach it to flak vest with the black plastic snap-release buckles.
  6. Black gauntlet-style gloves (flared leather or pleather preferred, cloth or rubber gloves will not meet standards)

Formal Requirements:
You must have at least one of the following items to be accepted:

  1. B-Wing hard helmet with Star Wars-style decoration.
  2. Cloth tan AN-H-15 flight helmet (or replica)
  3. X-Wing helmet with Star Wars-style decoration.
  4. Y-Wing helmet with Star Wars-style decoration.
  5. Mini-flares on web belt. A mix of filled and empty slots are okay.
  6. Comm pad visible inside comm pad pocket on outside left forearm above wrist.

Optional:
  1. Metallic silver Code Cylinders (Arm Tools) in left shoulder pocket. Two minimum; four maximum. Cylinder heads showing should resemble screen accurate representations.
  2. Breathing mask and tube as seen on Ten Numb in the Home One Briefing Room scene. Connects to the top right of the flak vest when not in use

Revised on June 1, 2010
===========================================
Note: For some events you may be required to have the correct helmet for your costume.
Specific Face Character pilots: Replicas of specific face characters (Wedge Antilles, for example) must have the correct helmet paint job.
===========================================

Baron/Colonel Fel Costume Standards


Required Items:
1. Black flightsuit in standard TIE/X-wing pilot style, with mandarin-style collar and pointed tab, code cylinder pocket on upper-middle left arm, rectangular pocket with a flap closure on upper-middle right arm, comm pad pocket on outside of left forearm above wrist, and thigh pockets (upper set required, lower set optional). No visible zippers or snaps. Flight suit must have red stripe running from where shoulder meets collar to wrist, and armpit to ankle on both sides.
2. Mid-calf black boots (Jack boots or engineer boots are acceptable. Leather pull-on style preferred with low heels. No laces. No ankle buckles (small buckle at top edge of boot allowable if covered by blousing). No non-black zippers. Any zipper closure must either be hidden or on the inside calf. No zippers on front or outside calf of boots. High-Calf boots are acceptable with sufficient blousing of the flighsuit legs.)
3. Silver/grey leg flares in an olive drab or black leg-band holder. Maximum of 8 flares per holder. Flares should be approximately 4" long.
4. Light grey/silver grey ejection harness and web belt, all 2” wide.
5. White or light grey flak vest with accurate ribbing and claps. (ANH & ROTJ versions should be sure to have the gap in ribbing on the upper chest. ESB Snowspeeder version is worn backwards.) Vest sizing should be proportional to the wearer.
6. Accurately sized grey chest box with accurate decoration (raised buttons (acrylic preferred, see the Pilot Forums for acceptable button color schemes), separated rocker switches, appropriate materialed greebles, pin stripes etc.). 1" - 1.75" diameter grey hose or aviation hose should attach at the left-bottom of the chestbox and connect to the suit in some screen-accurate manner (tucked up into the flak vest, attached to flightsuit, etc.). (Please note that Costumebase chestboxes will not pass the standards unmodified, however once slightly modified, they will meet standards.)
7. Metallic silver Code Cylinders (Arm Tools) in left shoulder pocket. Two minimum; four maximum. Cylinder heads showing should resemble screen accurate representations
8. Black gauntlet-style gloves (flared leather or pleather preferred, cloth or rubber gloves will not meet standards)
9. Accurate Comm Pad (size, details, 3-dimensional, coloration, etc.) visible in the correct comm pad pocket on outside left forearm above wrist. (May be either the white X-wing version or the black TIE version.)
10. Hair must be black/colored black and combed back in "widow's peak" style haircut.
11. Facial hair cut in "goatee" style or a consistent "five o'clock shadow."

Formal Requirements:
You must have at least one of the following items to be accepted:


1. X-Wing helmet with Baron Fel style decoration.
2. Mini-flares on belt - a mix of filled and empty slots are okay.
3. Accurate belt buckle on web belt.


Added by LMO on 30 November, 2010
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> COSTUME STANDARDS All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot post calendar events in this forum
The Rebel Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred volunteer Rebel costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © 2014 Lucasfilm Ltd. & ™ All rights reserved. Used under authorization.


Powered by phpBB © 2001, 2005 phpBB Group