Forum and Costume Controls

   FAQFAQ  SearchSearch  MemberlistMemberlist   UsergroupsUsergroups  medals.php?sid=b7a8000bfe0043a240461568f297b7bdMedals   RegisterRegister   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in

       
REMINDER: Do not change your e-mail address yourself. Please read this first for why.

[Revision] Temple Guard The Clone Wars

 
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> Jedi -> KJO Standards Development -> KJO Standards Archive
View previous topic :: View next topic  
Author Message
AhsokaFreakingTano (Kelly Hawthorne)
Active Legion Member


Joined: 14 Oct 2015
Posts: 336
Location: Utah
Medals: None

PostPosted: Wed Jun 05, 2019 7:57 pm    Post subject: [Revision] Temple Guard The Clone Wars Reply with quote

The discussion will be open for two weeks and close on June 19th standard will then go to vote.

Image Gallery: http://www.kjo.rebellegion.com/?portfolio=jedi-temple-guard-tcwLink to current Costume Standard: http://newsite.rebellegion.com/jedi-temple-guard-the-clone-wars/

Hood:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/459.jpg
Hood is made from suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
The main body of the hood is cream/off-white with a 2-3in wide edge of the tan colored fabric of the same material
At the top of the hood, starting at upper portion of the forehead the tan cuff curves to make a half oval shape at the top of the hood.
The tan cuff continues on the inside of the wearer's hood.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/274.jpg
Hood has an overall billowed appearance
Optional: Tan continues inside the hood as a lining.
Hood attaches to the shoulder piece at the back with a downwards taper that continues beyond the top edge of the tabbard
In the back where the hood and shoulder piece meet the hood billows slightly
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/551-680x713.jpg
Hood tucks inside the shoulder piece at the front
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/333-680x543.jpg

Mask:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/459.jpg
May be either a mask or full helmet as long as no visible edge is seen through the top/side of hood. It is a hard/reflective material with appropriate detail applied. Costumer’s eyes should not be visible.
Mask is either a mask only or full helmet so long as no visible edge is seen through the top or side of the hood.
Mask must cover the full face of the wearer.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/451-680x525.jpg
Mask is a matte white in color with eye cutouts matching references, wearer’s eyes are not visible.
Gold detailing is painted on matching references and should have a 3D effect if the details are not slightly raised from the mask.
Optional: Preferred that gold detailing be raised slightly from the overall mask but not required

Shoulder Piece
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/274.jpg
Shoulder piece is made from a cream/off-white material that comprises of suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
In the back the shoulder piece is connected to the hood with the hood billowing over the seam line slightly
The back of the shoulder piece ends at the bottom of the wearer’s shoulder blades
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/551-680x713.jpg
In the front the shoulder piece goes over the hood and shirt.
The shoulder piece extends past the tabards and shoulders of the wearer to create a small cap (approx. 3in from the shoulder of the wearer) cap is proportional to the wearer.
On each shoulder there is a gold design on the sleeve cap, design is flush with the edge of the shoulder piece
Design can be painted, vinyl transfer, or applique so long as it sits flush with the base material.
Design can have a metallic sheen but is not shiny.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/451-680x525.jpg


Tabards:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/451-680x525.jpg
The tabards are made from the same material as the shoulder piece: a cream/off-white material that comprises of suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
In the back the tabard is a single piece that starts with a curve following the shoulder piece and begin tapering to a gradually smaller width at the inside shoulder of the wearer making a “Y” shape.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/551-680x713.jpg
Tabard tucks into the belt at the back.
In the front tabards cross in the front with the left side crossing over the right and tucking into the belt, the ride side of the tabard goes under the left piece and ends at or under the left tabard.
Tabards extend approx. 1.5-2.5in from the wearer’s shoulders following the same cap curve as the shoulder piece, tabards do not extend nor do they meet the same width at the shoulders as the shoulder piece.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/274.jpg
On the tabards there are gold designs matching references
Design can be painted, vinyl transfer, or applique so long as it sits flush with the base material. ***no dimension edit**
Design can have a metallic sheen but is not shiny.

Chest:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/451-680x525.jpg
The chest piece is made from the same material as the shoulder piece and tabards: a cream/off-white material that comprises of suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
Chest piece ends at least at the shoulder seam of the shoulder piece and runs down in a straight line following the contours of the wearer.
At the bottom of the bust the chest piece come in at a slight angle inwards towards the body of the wearer and continues down straight until it tucks into the belt.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/066.jpg
The chest piece rests under the tabards and shoulder piece and it does not come higher than the top of the shoulder piece and hood in the front.
Optional: The hood can attach to this piece at the front, starting in front of the shoulder seam of the shoulder piece, this will allow the hood to stay down easier.


Shirt and Undershirt/dickie:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/363-680x588.jpg
No skin should be visible.
Shirt:
The shirt made from the same material as the skirt in the same color: a tan/beige material that comprises of suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
Shirt is form fitting but not skin to the wearer.
Shirt has a “V” neckline that ends at the Jugular notch of the wearer.
Optional: Shirt can have the attached high overlapping collar, collar can be a seperate piece from the shirt so long as it fits snug to the neckline.
Undershirt/Dickie:
This is optional if the high fold over collar is attached to the shirt.
High collar that comes up on the wearer’s neck
Collar is made from the same material and is the same color as the shirt.
Collar folds left over right with an edge band that is approx. 1in
Collar tucks into and under the neckline of the shirt (if it is a seperate piece)
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/459.jpg


Bracers/hand plates:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/52_edited-680x722.jpg
Bracers/hand plates are made from either: leather or leather-like material or the same material as the rest of the pieces: suede, micro-suede, calf-skin or similar and has a texture similar to those materials.
Bracers are stiff and not have any creases or bends in the material.
Bracers are a slightly darker tan/light brown from the shirt but are not the same colors as any of the other pieces.
Bracers have two (2) darker straps on the front of the forearm that are approximately 1-1.5in in width and come to a point at each end
The hand plate is attached to the main body of the bracer
There is a front top cuff piece that only covers the front half of the bracer and is attached to the main body of the bracer.
Bracers should be form fitting to the wearer
The shirt tucks into the bracers and the bracers rest over the gloves.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/383-680x375.jpg

Gloves:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/374.jpg
Gloves made of similar material and are the same color as the shirt.
Gloves tuck under the bracers

Belt:
The belt is made up of four portions which include the following: Main center part, Upper portion, short lower panel, long lower panel.
Belt is made from leather or leather like material with that kind of texture.
Main center part:
The main center part of the belt has a middle portion that is recessed from the top and bottom portion of this part with the top portion being thinner than the recessed portion and the bottom raised portion.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/571.jpg
In the back of the belt this bottom raised portion gets slightly wider with a gentle curve
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/491-680x686.jpg
In the front of the belt there is a buckle that rest over top of the belt, on either side are rectangles of the of brown that can be the same material as the belt in the middle is a strip running across it also in brown, and can be same material as belt.
Buckle should be in proportion to the wearer and have accurate details, cutouts, lines, and indents matching references
Buckle part that is not brown is painted a dark grey color and can be metallic but not shiny.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/004-680x481.jpg
Upper portion:
The upper portion of the belt is the same thickness as the top raised portion of the main center part.
The top part comes up at a square from the middle of the brown rectangles that edge either side of the buckle.
The top part has a gradual curve that come up to be higher in the back than it is in the front following the contours of the wearer’s hip bones as reference.
The top part fits flush against the wearer and does not stick out.
Short lower panel:
The short lower panel rests under the main part of the belt but over the longer lower panel and is thinner in thickness than the main belt’s raised portions.
The short panel starts at the skirt’s darker panel trim, on either side, going straight down and is longer around the wearer than the long lower panel.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/402-680x658.jpg
The bottom edge come down in a gradual curve to its final length but makes for angles into the bottom edge at the at the back of the belt
The short panel does not wrap all the way around the back of the wearer.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/491-680x686.jpg
Long lower panel:
The long lower panel is an overall rectangular piece that fits the wearer but is not perfectly flush at the bottom to the skirt
The front edges of this panel start after the short lower panel and after the start of the skirt’s top panel.
In the back of this panel that is a trapezoidal shaped cut out that brings the back center portion higher than the overall edge of this panel.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/491-680x686.jpg
Accessories:
There are twelve (12) keys hang from the belt on angular rings that attach under the main belt.
There are two key designs that repeat in either a silver/grey metallic or a gold metallic
Keys change their orientation (mirrored)
In the back there is a rectangular flap/pouch that attaches to the main center part of the belt
Flap/pouch is the same color as the buckle
Saber clip:
Covertec clip or similar to hold saber if saber is present
Clip can be a gold in the same color as the keys or black.


Skirt:
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/00c1.png
The skirt is made from the same material as the shirt in the same color: a tan/beige material that comprises of suede, micro-suede, calf-skin or similar and has a texture similar to those.
The skirt reaches to the ankle of the wearer
In the front the skirt has a squared off opening that starts on the upper thigh of the wearer
This squared off portion is no wider than the buckle on the belt and is proportional to the wearer.
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/234.jpg
The bottom of the skirt, at the front, the the skirt is angled back and down to meet the hem.
Skirt is trimmed all the way around the edge in a band (approx. 1-1.5in) in width of the same cream/off-white material as the hood, chest piece, tabards, and shoulder piece.
On the skirt there is a darker tan/light brown panel that extends just below the knee and wraps all the way around the skirt.
The material of the skirt is made from the same material as the rest of the costume but is a slightly darker color.
Color options: a darker tan/light brown or khaki that is darker than the main body of the skirt. Color is not as dark as the pants, or as dark as the bands on the bracers.
The panel has a large herringbone pattern which can be painted, etched, or quilted onto the fabric
Square quilting is allowed but herringbone preferred.
The panel is trimmed all the way around the edge in a band (approx. 1-1.5in) in width of the same material used for the skirt trim
Optional: the trim is attached to the skirt body and the panel is attached on it’s own for a more accurate look to the references to give the panel a raised appearance but is still attached to the main body of the skirt.
Skirt comes up under the belt, can be attached to the shirt.

Pants:
Dark brown fitted but not skin tight pants with no visible pockets (pockets that are not visible are allowed)
Pants tuck into the boots

Boots:
Two tone boot that rises to just below the knee with a front extension to cover the kneecap.
Color options: two colors of brown (one lightere and one darker), brown and grey, or brown and taupe


Saber (optional):
Image URL: http://www.kjo.rebellegion.com/wp-content/uploads/2014/07/00c1.png
A double staff yellow bladed saber is allowed
A screen accurate temple guard saber is preferred but not required.
Hilt only are allowed and should be accurate to the references
If bladed, blades should be yellow.

Balaclava (optional):
Balaclava is optional if the wearer’s skin/hair shows in the costume otherwise.
Of tan or light brown material in line with the rest of the costume.
Close fitting/skin-tight to the wearer.
Bottom edge extends inside collar of the shirt.
Wearer’s skin/hair is not visible.


Last edited by AhsokaFreakingTano (Kelly Hawthorne) on Sun Jun 16, 2019 11:06 pm; edited 1 time in total
Back to top
View user's profile Send private message
Larirenshadow ()
Base Membership Officer


Joined: 04 Sep 2016
Posts: 343
Location: Northern California
Medals: 1 (View more...)
Troopers Helping Troopers (Amount: 1)

PostPosted: Wed Jun 05, 2019 8:06 pm    Post subject: Reply with quote

Is there a way to clarify for the boots? The standard just says two tons but maybe specify the brown tones desired?
_________________
Endor Base Membership Officer and Head Regional Captain
Rebel of the Year 2018
Back to top
View user's profile Send private message
AhsokaFreakingTano (Kelly Hawthorne)
Active Legion Member


Joined: 14 Oct 2015
Posts: 336
Location: Utah
Medals: None

PostPosted: Wed Jun 05, 2019 8:09 pm    Post subject: Reply with quote

Larirenshadow wrote:
Is there a way to clarify for the boots? The standard just says two tons but maybe specify the brown tones desired?


Well, I left that alone because in some shots they look brown and brown, in others toupe and brown, brown and grey, grey and grey.
The gallery doesn't have many clear images for me, and looking at youtube videos, didn't help much either however: if you have a clearer image, add a link.
Thanks
Back to top
View user's profile Send private message
AhsokaFreakingTano (Kelly Hawthorne)
Active Legion Member


Joined: 14 Oct 2015
Posts: 336
Location: Utah
Medals: None

PostPosted: Sun Jun 16, 2019 11:07 pm    Post subject: Reply with quote

On the boots: added color options based off currently available references.
Back to top
View user's profile Send private message
AhsokaFreakingTano (Kelly Hawthorne)
Active Legion Member


Joined: 14 Oct 2015
Posts: 336
Location: Utah
Medals: None

PostPosted: Wed Jun 19, 2019 5:22 pm    Post subject: Reply with quote

with no other discussion or changes, this thread is locked and now goes to vote.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   This topic is locked: you cannot edit posts or make replies.    Rebel Legion Forum Index -> Costume and Prop Making -> Jedi -> KJO Standards Development -> KJO Standards Archive All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can post calendar events in this forum
The Rebel Legion is a worldwide Star Wars costuming organization comprised of and operated by Star Wars fans. While not sponsored by Lucasfilm Ltd., it is Lucasfilm's preferred volunteer Rebel costuming group. Star Wars, its characters, costumes, and all associated items are the intellectual property of Lucasfilm. © 2019 Lucasfilm Ltd. & ™ All rights reserved. Used under authorization.


Powered by phpBB © 2001, 2005 phpBB Group